Zkteco Sf300 Wiring Diagram

Download the latest product installation guides here and learn the basic guides on how to install time attendance, access control, entrance control, pos, etc. In the devices possessing photo id function, figure 4 will be displayed on screen after succ essful

Біометричний термінал по відбитку пальця MA300 ZKTeco

Tamper proof switch and multiple alarm outputs.

Zkteco sf300 wiring diagram. “wet mode” wiring diagram of lock connecting with external power supply. Is shown in pc software. The sf300 is an ip based fingerprint terminal, which operate in both network mode and standalone mode.

• if the door lock runs on 12v dc, but requires more than 1a (amp), then provide separate power to the door lock. Ma300 intercom system pdf manual download. Tcp/ip communication for various networking environments.

Instructions for installation and use of the c3100/200/400 control panel version: The ever popular zkteco ma300 with metal casing and ip65 rating. Zkteco sf300 is an ip based fingerprint terminal, which operate in both network mode and standalone mode.

Wiegand output makes sf300 flexible to connect with zk or any 3rd party controllers as a slave reader, additionally, wiegand input allows two units of. In network mode, sf300 can connect with zkaccess3.5 software for access control and time attendance management. Tamper proof switch and multiple alarm outputs.

It can connect with zkaccess3.5 software for access control and time attendance management. 1)after a user swipes the management card seven times, if the last (i) to prevent the interference, the last device in the rs485 bus connect a 120 euro resistor.

Wiegand output makes sf300 flexible to connect with zk or any 3rd party controllers as a slave reader, additionally, wiegand input allows two units of zkteco. Shown as figure 3, 4. The sf300 is an ip based fingerprint terminal, which operate in both network mode and standalone mode.

Supports usb flash drive for offline data management. Power wiring diagram without backup battery with backup battery switching power supply ground ground switching power supply figure 14 figure 13. 5please connect the gnd before all the other wiring especially under the environment with much electrostatic.

Tcp/ip communication for various networking environments. T h ema300 s up or trs485 a df n ci , a d it c n be c to the fr1200 reader through the rs485.the rs485 reader function can b esw itchd by p ng mard v. Wiegand output makes sf300 flexible to connect with zkteco or any 3rd party controllers as a slave reader, additionally, wiegand input allows two units of sf300 to configure with each other and utilize master & slave solution, which requires user verification at both entrance and exit.

5please connect the gnd before all the other wiring especially under the environment with much electrostatic. The sf300 is an ip based fingerprint terminal, which operate in both network mode and standalone mode. Tcp/ip communication for various networking environments.

Zkteco biometric access control devices, by default, it is set with wiegand 26. When wiring is complete reconnect the battery negative terminal. 7 however, in the following three scenarios, it is recommended that the door lock has an independent power source, and is not powered by the device;

1.0.1 date:oct.2010 about this manual this manual is a guide to installation and connection of the c3100/200/400 access Supports usb flash drive for offline data management. It can connect with zkaccess3.5 software for access control and time attendance management.

Zkteco is open for custom designs and software development kits are available on our products to be able to custom a solution for the client. You can change it as follows. It can connect with zkaccess3.5 software for access control and time attendance management.

(ii) the rs485 device no. 12 inbio pro series access control panels installation guide rs485 fingerprint reader connection 12v dc 12v dc ethernet 1 82 3 rs485 fingerprint reader Power wiring diagram without backup battery with backup battery switching power supply ground.

If qr500 connects zk controller connection correctly, the devices will be paired automatically without special configuration. Supports usb flash drive for. That is turning the switch ‘4’ (terminal resistor switch) to ‘on’.

• if the door lock voltage is not 12v dc then provides separate power to the door lock. It can connect with zkaccess3.5 software for access control and time attendance management. Zkteco india focus on biometrics of fingerprint, face recognition, finger and iris recognition, provides products of biometric attendance, access control, video surveillance, entrance control, smart lock, pos.

Wiegand output makes sf300 flexible to connect with zk or any 3rd party controllers as a slave reader, additionally, wiegand input allows. Download the latest zkteco product user manual of time attendance, access control, entrance control, security inspection, smart lock, cctv, and pos products. Installation diagram about qr500 connection with zkteco access control and control panel.

Enlarged diagram of lock ports nc lock lock power l input diode diode jumper terminal 1.tcp/ip communication 2.rs485 communication the background pc software is able to communicate with the system according to two protocols(rs485 and tcp/ip) for data exchange and. Zkteco sf300 is an ip based fingerprint terminal works both in network and standalone modes. Wiring diagrams bmw 3 series e30 e36 e46 z3 5 series e28 e34 e39 6 series e24 7 series e23 e32 e38 8 series e31.

Tamper proof switch and multiple alarm outputs. Be advised that wiring the device while power is on may cause damage to the terminal. Wiring diagram on qr500 and access control.

Wiegand output makes sf300 flexible to connect with zk or any 3rd party controllers as a slave reader. This feature is not available right now.

Zkteco K40 Wiring Diagram Wiring Diagram Schemas